纳米ZnO的阳极消耗法制备和表征

采用阳极消耗法制备了纳米ZnO粉体,并利用XRD,TEM,XPS,UV-V is和PL测试技术对样品进行了表征.结果表明,所制样品为纤锌矿结构的纳米ZnO,颗粒呈类球形,平均粒径15 nm,具有很强的紫外吸收能力.位于531.44 eV的O1 s峰和PL谱上的绿带共同证明了氧空位存在,纳米ZnO的绿光发射带来自氧空位电子与价带空穴的辐射复合.     

Cu-P系稀土耐候钢中最佳稀土含量的研究

利用光学显微镜、图像分析仪和电子探针对低氧低硫的10PCuRE耐候钢板坯进行了观察和检测,采用干-湿周浸室内加速试验方法测得了试验钢的腐蚀率.用电化学方法测得了带锈样的阳极极化曲线.研究得出对于S:～0.004%,O:～0.002%的10PCuRE耐候钢,最佳稀土含量为0.0065%～0.012%,此稀土含量对非金属夹杂物的变质作用和耐蚀性能的提高最为有利.     

Application of heat conduction calorimetry to high explosives

This paper describes some thermal analysis experiments conducted on high explosive samples. These employ differential scanning calorimetry to monitor thermal effects at elevated temperatures (around 200 °C) and heat conduction calorimetry to record thermal effects at much lower temperatures (below 100 °C).The work shows that, due to the generally high thermal stability of many high explosive compositions, heat generation rates are very low, if detectable at all, at normal storage temperatures, even when using a very sensitive instrument. The sensitivity and reproducibility of this technique has been investigated in detail by Wilker et al. [S. Wilker, U. Ticmanis, G. Pantel, Detailed investigation of sensitivity and reproducibility of heat flow calorimetry, in: Proceedings of the 11th Symposium on Chemical Problems Connected with the Stability of Explosives, Sweden, 1998] and shown to be capable of recording heat generation rates of less than a microwatt. This allows continuous measurement of decomposition processes in nitrate ester based propellants at temperatures as low as 40 °C. However, the measurement of very low levels of heat generation is difficult, time consuming and therefore expensive. If the assumption is made that the life limiting process is invariably the slow decomposition of the energetic component, this will frequently lead to very long service lifetime predictions.A number of possible complications are identified. Firstly, due to its low detection threshold, a heat conduction calorimeter may detect other reactions which will not lead to failure, but which may still dominate the heat flow signal. Secondly, the true failure process may generate little energy and be overlooked. In view of these considerations, at present it seems unwise to rely on heat conduction microcalorimetry as the only tool for the assessment of the life of high explosive energetic systems.Based on examples of life terminating processes in high explosives during storage and use, it is clear that decomposition of the energetic material is not invariably the cause of system failure. It is also by no means the only reaction that may take place in, and be observed by, a heat conduction calorimeter.     

Cerium hybrid silica coatings on stainless steel AISI 304 substrate

AISI 304 Stainless Steel is widely used in different industrial fields because of its mechanical and corrosion properties. However, its tendency to corrosion in presence of halide ions limits the applications. One strategy to improve the corrosion resistance is the use of coatings barriers containing corrosion inhibitors in their formulation. The lanthanides present attractive green and corrosion properties for the substitution of chromates, which are the most common substances used as corrosion protection. However, these compounds are highly toxic, and an intense effort is being undertaken to replace them. Cerium is a good alternative because of its relatively low cost and abundance. It fulfils the basics requirements for being considered an alternative inhibitor: the ions form insoluble hydroxides and they present low toxicity. Inorganic and hybrid sol-gel coatings have been developed to increase the corrosion resistance of metals and they provide an excellent vehicle for the incorporation of secondary phases including particles and metal ions as cerium ions. The aim of this work was to study the influence of the incorporation of cerium ions in hybrid silica sol-gel coatings deposited on AISI 304 stainless steel as substrate as a potential replacement of chromate treatments. This system should combine the barrier protection effect of silica coating with the corrosion inhibitor effect of the cerium ions inside the coatings. After 7 days of immersion in NaCl, coated substrates showed lower current densities than the bare steel, although the coatings produced from Ce (III) salts experience a slight weakening in time and those obtained from Ce (IV) chemicals evidence an enhance in the coating performance, probably due to the plugging of corrosion products in the defective areas of the film.     

Stainless steel capillary columns for high temperature gas chromatography

A layer of elemental silicon has been deposited on the surface of stainless steel tubing by means of chemical vapor deposition (CVD). Two kinds of capillary column were prepared from the deactivated tubing: cross-linked, silanol-terminated polydime-thylsiloxane wall coated open tubular (WCOT) columns and molecular sieve 13X porous layer open tubular (PLOT) columns. Unlike fused silica capillary columns, stainless steel WCOT and PLOT columns can be operated at temperatures in excess of 400°C. High temperature simulated distillation has been performed successfully with a macro bore WCOT column and rapid PNA (paraffin, naphthene, and aromatic) analysis with a multidimensional gas solid chromatographic (GSC) system using PLOT columns.     

Mass spectrometric diagnosis of the surface nitriding mechanism in a d.c. glow discharge

Reactive constituents have been investigated in a molecular beam generated in the cathode surface glow area and surface boundary layer. Mixtures of nitrogen and hydrogen form NH_x(x=0–4) compounds, which are of relevance in heterogeneous, plasma vs. metal nitriding reactions. Ammonia decomposition leads to NH_x(x=2–4). Strong cataphoretic enrichment of hydrogen has been observed in the cathode glow area. Heterogeneous reactions of NH_x with iron lead to the formation of iron nitrides via intermediates such as FeNH_2–3. In a pulsed d.c. glow discharge, increased sputtering and decreased hydrogen enrichment have been observed.     

Preparation of Fe/B powders by mechanical alloying

Steels with a high boron content are valuable as a neutron shield in waste containers and as control absorbers in nuclear reactors. The purpose of this study was to obtain by mechanical alloying an iron powder with 50% boron (by weight) and then powder-metallurgy materials. The elementary powders were mixed in a high-energy mill for 36 h in an inert atmosphere. Samples were withdrawn at intervals, and the powder was characterized by differential thermal analysis, X-ray diffraction and electron microscopy. The Fe/B powders withdrawn at different intervals of milling were diluted with further additions of iron up to a final content of 10% boron. The mixtures were uniaxially compacted at 500 MPa; their green density was verified, and they were sintered in argon at 1150°C. Their physical properties (density and dimensional change) and bending strength were evaluated and microstructural studies and fracture tests were performed.     

Electrocatalytic properties of surface oxides on gold,platinum, and stainless steel electrodes in electrooxidation of malic acid

Electrocatalytic properties of oxides formed at gold, platinum, and stainless steel electrodes in the malic acid electrooxidation in 0.1 M Na₂SO₄ are studied. Gas chromatographic analysis of the electrolyte after holding the potential at 1.0 V for 8 h shows that on platinum and gold electrodes 2 mmol of acetaldehyde are produced and on stainless steel, 45 mmol. The acetaldehyde yield is the highest on stainless steel.From Elektrokhimiya, Vol. 41, No. 3, 2005, pp. 304–309.Original English Text Copyright © 2005 by Avramov Ivi, Popi, Antonovi.This article was submitted by the authors in English.     

基于物联网的医用耗材智能屋管理系统

针对医用高值耗材种类繁多、管理难度大的问题,为减少人力成本、提高医用高值耗材的智能化管理水平。本文提出了基于物联网的高值医用耗材智能屋的管理系统,介绍了智能屋的整体架构、系统功能、核心业务及流程设计,主要分为结构模块、RFID模块、数据库模块、控制系统模块四大模块,具体有用户管理、出入库管理、综合查询、预警管理四大业务,通过GM(1,1)模型对2022年全年高值医用耗材的月消耗量进行预测分析,并且检验得该预测模型的精度等级为一级,模型预测效果很好,能够为医院采购人员采购提供了一个参考,避免因过度的主观估计而造成的耗材浪费。该系统能够有效地提高医院对于高值医用耗材的管理水平,减少人力、物力和财力的消耗,为广大患者提供更加优质的医疗服务。本文所提的高值医用耗材智能屋管理系统解决了传统的高值医用耗材管理的诸多难题。     

基于新型核与灰度序列的时滞GM(1,N)模型及其应用

为了解决GM(1,N)模型在新型核与灰度的基础上,对驱动项的延迟作用机理不明确的问题,将时滞参数引入到GM(1,N)模型的驱动项中,构建了基于新型核与灰度的时滞GM(1,N)模型,分析了时滞参数的辨识方法,讨论了新模型的建模机理。为了更好地对该模型的有效性进行验证,将优化的时滞GM(1,N)模型对南京市的雾霾进行预测分析,选择GM(1,N)模型、一元回归模型与文中的优化模型进行对比。结果显示,优化模型对PM₁₀浓度的拟合精度更高,且误差均控制在5%之内,从而验证了提出的优化模型适用于具有时滞特征数据的模拟和预测。